VOR1142B4 www.vishay.com vishay semiconductors rev. 1.0, 09-jun-16 1 document number: 84299 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 1 form a solid-state relay description the vor1142 is a 400 v single channel normally open optically isolated solid-state relay (spst - 1 form a). based on hybrid architecture which allows fast switching times with a wide operating ambien t temperature range. a high efficient gaalas ired enables low forward current on the input side. on the output si de high performance mosfet switches provide a low r on and can switch both dc and ac signals. features ? isolation test voltage 5300 v rms ? typical r on 22 ? load voltage 400 v ? load current 140 ma ? clean bounce free switching ? current limit protection ? low power consumption ? wide temperature range ? material categorization: fo r definitions of compliance please see www.vishay.com/doc?99912 applications ? general telecom switching ? metering ? security equipment ? instrumentation ? industrial controls ? battery management systems ? automatic test equipment agency approvals ? ul1577, file no. e52744 ? din en 60747-5-5 (vde 0884-5) a c s 1 s 2 4 3 1 2 ordering information vor1 1 4 2b4 # part number package configuration package ul, vde smd-4, tape and reel VOR1142B4t smd-4, tube VOR1142B4 s md-4
VOR1142B4 www.vishay.com vishay semiconductors rev. 1.0, 09-jun-16 2 document number: 84299 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? stresses in excess of the absolu te maximum ratings can ca use permanent damage to the device. functional operation of the devic e is not implied at these or any other conditions in excess of those give n in the operational sections of this document. exposure to abs olute maximum ratings for extended periods of th e time can adversely affect reliability. note ? minimum and maximum values are testing requirements. typical values are characteristics of the device and are the result of en gineering evaluations. typical values are for information only and are not part of the testing requirements. absolute maximum ratings (t amb = 25 c, unless otherwise specified) parameter condition symbol value unit input ired continuous forward current i f 50 ma ired reverse voltage v r 5v input power dissipation p diss 80 mw output dc or peak ac load voltage v l 400 v continuous dc load current at 25 c, bidirectional i l 140 ma ssr output power dissipation p diss 550 mw ssr ambient temperature range t amb -40 to +100 c storage temperature range t stg -40 to +150 c soldering temperature t = 10 s max. t sld 260 c electrical characteristics (t amb = 25 c, unless otherwise specified) parameter test condition symbol min. typ. max. unit input ired forward current, switch turn-on i l = 100 ma, t = 10 ms i fon -0.252 ma ired forward current, switch turn-off v l = 350 v, i l < 1 a i foff 0.05 0.15 - ma ired forward voltage i f = 10 ma v f - 1.36 1.5 v ired reverse current v r = 5 v i r - - 10 a output on-resistance, ac/dc: pin 3 () to 4 () i f = 5 ma, i l = 50 ma r on -2227 off-resistance i f = 0 ma, v l = 100 v r off 1 5000 - g off-state leakage current i f = 0 ma, v l = 100 v i o - < 1 100 na i f = 0 ma, v l = 400 v i o - 6 500 na output capacitance pin 3 to 4 i f = 0 ma, v l = 1 v, 1 mhz c o -39-pf i f = 0 ma, v l = 50 v, 1 mhz c o -6-pf current limit ac/dc i f = 5 ma, t = 5 ms, v l = 6 v i limit 170 300 450 ma transfer capacitance (input to output) v io = 1 v c io -1-pf switching characteristics (t amb = 25 c, unless otherwise specified) parameter test condition symbol min. typ. max. unit turn-on time i f = 5 ma, i l = 50 ma t on - 0.13 0.5 ms turn-off time i f = 5 ma, i l = 50 ma t off - 0.05 0.2 ms
VOR1142B4 www.vishay.com vishay semiconductors rev. 1.0, 09-jun-16 3 document number: 84299 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 1 - timing schematic note ? as per iec 60747-5-5, 7.4.3.8.2, this opto coupler is suitable for saf e electrical insulation only within the safety rating s. compliance with the safety ratings shall be ensured by means of protective circuits. fig. 2 - safety power dissipation vs . ambient temperature fig. 3 - safety input current vs. ambient temperature safety and insulation ratings parameter test condition symbol value unit climatic classificati on according to iec 68 part 1 40 / 100 / 21 pollution degr ee according to din vde 0109 2 comparative tracking index i nsulation group iiia cti 175 maximum rated withstanding isolation voltage according to ul1577, t = 1 min v iso 5300 v rms maximum transient isol ation voltage according to din en 60747-5-5 v iotm 8000 v peak maximum repetitive peak isolation voltage according to din en 60747-5-5 v iorm 890 v peak isolation resistance v io = 500 v, t amb = 25 c r io 10 12 v io = 500 v, t amb = 100 c r io 10 11 output safety power p so 720 mw input safety current i si 240 ma safety temperature t s 175 c creepage distance 8mm clearance distance 8mm insulation thickness dti 0.4 mm input to output test voltage, method b v iorm x 1.875 = v pr , 100 % production test with t m = 1 s, partial discharge < 5 pc v pr 1669 v peak input to output test voltage, method a v iorm x 1.6 = v pr , 100 % sample test with t m = 10 s, partial discharge < 5 pc v pr 1424 v peak input output 90 % 10 % t on t off a c v l output 1 2 4 3 0 200 400 600 800 -50-250 255075100125150175 p s o -output s afety power (mw) t amb - ambient temperature ( c) 0 50 100 150 200 250 -50-250 255075100125150175 i s i - input s afety current (ma) t amb - ambient temperature ( c)
VOR1142B4 www.vishay.com vishay semiconductors rev. 1.0, 09-jun-16 4 document number: 84299 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 typical characteristics (t amb = 25 c, unless otherwise specified) fig. 4 - maximum load current vs. ambient temperature fig. 5 - forward voltage vs. ambient temperature fig. 6 - forward current vs. forward voltage fig. 7 - normalized forward current for switch turn-on vs. ambient temperature fig. 8 - normalized on-resistance vs. ambient temperature fig. 9 - output capaci tance vs. load voltage 0 30 60 90 120 150 -40-200 20406080100 i l - load current (ma) t amb - ambient temperature ( c) 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 -40-200 20406080100 v f - forward voltage (v) t amb - ambient temperature ( c) i f = 10 ma i f = 5 ma i f = 2 ma 0 10 20 30 40 50 60 0 0.5 1.0 1.5 2.0 i f - forward current (ma) v f - forward voltage (v) t = 100 c t = 25 c t = -40 c 0 0.5 1.0 1.5 2.0 2.5 -40-200 20406080100 normalized forward current for s witch turn-on t amb - ambient temperature ( c) normalized to t amb = 25 c i l = 100 ma 0 0.5 1.0 1.5 2.0 -40-200 20406080100 normalized on-re s i s tance t amb - ambient temperature ( c) normalized to t amb = 25 c i f = 5.0 ma i l = 50 ma 0 10 20 30 40 50 60 0 102030405060 s witch capacitance (pf) v l - load voltage (v) i f = 0 ma f = 1 mhz
VOR1142B4 www.vishay.com vishay semiconductors rev. 1.0, 09-jun-16 5 document number: 84299 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 10 - off-state leakage current vs. load voltage fig. 11 - turn-on time vs. forward current fig. 12 - normalized turn-on time vs. ambient temperature fig. 13 - turn-off time vs. forward current fig. 14 - normalized turn-off time vs. ambient temperature 0.01 0.1 1 10 100 0100200300 off- s tate leakage current (na) v l -load voltage (v) t = 100 c t = 25 c t = -40 c i f = 0 ma 0 0.5 1.0 1.5 2.0 0 1020304050 turn-on time (m s ) i f - forward current (ma) t = 100 c t = 25 c t = -40 c i l = 50 ma 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 -40 -20 0 20 40 60 80 100 normalized turn-on time t amb - ambient temperature ( c) normalized to t amb = 25 c i f = 5 ma 0 0.04 0.08 0.12 0.16 0.20 0 1020304050 turn-off time (m s ) i f - forward current (ma) t = 100 c t = 25 c t = -40 c i l = 50 ma 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 -40-200 20406080100 normalized turn-off time t amb - ambient temperature ( c) normalized to t amb = 25 c i f = 5.0 ma
VOR1142B4 www.vishay.com vishay semiconductors rev. 1.0, 09-jun-16 6 document number: 84299 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 package dimensions in millimeters smd-4 package marking (example) fig. 15 - VOR1142B4 note ? package configuration (t, a, b) are not part of the package marking. 5.08 max. 4.69 0.13 0.79 typ. 1.00 0.10 2.54 nom. 3.55 0.25 0.25 0.20 7.62 typ. 6.65 0.15 8.00 min. 9.80 0.25 0.60 min. 0.25 0.10 lead s coplanarity 0.1 max. 8.0 min. 11.00 1.50 2.54 1.50 recommended footprint pin 1 i.d. 43 12 1142 v yww 68
VOR1142B4 www.vishay.com vishay semiconductors rev. 1.0, 09-jun-16 7 document number: 84299 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 packing information (in millimeters) fig. 16 - tape and reel packing solder profiles fig. 17 - lead (pb)-free reflow solder profile according to j-std-020 for smd devices handling and storage conditions esd level: hbm class 2 floor life: unlimited conditions: t amb < 30 c, rh < 85 % moisture sensitivity level 1, according to j-std-020 tape and reel packing type units/reel smd-4 1000 tube packing type units/tube tubes/box units/box smd-4 100 20 2000 2 0.1 4 0.1 1.75 0.1 12 0.1 4.95 0.1 1.5 min. 10.2 0.1 pin 1 7.5 0.1 16 0.3 0.35 0.05 4.07 0.1 c l 3.68 0.1 1.5 min. 0 50 100 150 200 250 300 0 50 100 150 200 250 300 time (s) temperature (c) 240 c 245 c max. 260 c max. 120 s max. 100 s 217 c max. 30 s max. ramp up 3 c/s max. ramp down 6 c/s 19841 255 c
legal disclaimer notice www.vishay.com vishay revision: 13-jun-16 1 document number: 91000 disclaimer ? all product, product specifications and data ar e subject to change with out notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of th e products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product , (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all implied warranties, includ ing warranties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain types of applicatio ns are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular applic ation. it is the customers responsibility to validate tha t a particular product with the prope rties described in the product sp ecification is suitable for use in a particular application. parameters provided in datasheets and / or specifications may vary in different ap plications and perfor mance may vary over time. all operating parameters, including ty pical parameters, must be va lidated for each customer application by the customer s technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product could result in personal injury or death. customers using or selling vishay product s not expressly indicated for use in such applications do so at their own risk. please contact authorized vishay personnel to obtain writ ten terms and conditions rega rding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners.
|
